Downloads
Middle Control Download
Download the main Middle Control application for macOS or Windows. Middle Control for iOS is in development — leave your email to be notified when it is available.
The Middle Control app is free to use. On macOS, certain advanced features can be unlocked with a Pro license — see the section below for an overview of Pro features and how to upgrade: → Middle Control Pro
How to upgrade to Middle Control Pro
macOS only
After a 30-day free trial — which you can start directly within the macOS Middle Control app — you can purchase a license on our website. You will not be automatically charged when the trial ends. If you choose not to subscribe to a Pro license, the application will automatically revert to the standard (free) version of Middle Control at the end of the trial period.
The license can be used on up to 2 devices simultaneously. If you activate a third device, it will automatically deactivate the first registered device, etc.
Please note that the Middle Control Pro License cannot be refunded if it has been activated in the software. All purchases are final if activated
Middle Control Pro
Unlock exclusive features.
- Multi View (4 or 9 cameras)
- ATEM Link
- Automations
- Multi-operator control
- Replicate Settings
- Record Center (HyperDeck & ATEM recording)
- Video Output
- VISCA Controllers
- Canon RC-IP Controllers
Middle Control Pro features are available for macOS only.
One-time unlock — your Pro license stays valid in all future Middle Control versions, minor and major.
Feature Comparison: Pro vs Free
Feature support on macOS and Windows. The Windows column describes Middle Control 4.0 Beta; the stable Middle Control 2.7.4 for Windows has no direct Wi-Fi / Ethernet camera control and no Live View.
| Feature | Windows Free | macOS Free | macOS Pro |
|---|---|---|---|
| APC-R & APC-R Mini Support | ✓ | ✓ | ✓ |
| Middle Remote Support | ✓ | ✓ | ✓ |
| Gimbal Control | ✓ | ✓ | ✓ |
| Camera Control (via ATEM) | ✓ | ✓ | ✓ |
| Camera Control (via Wi-Fi / Ethernet) | ✓ | ✓ | ✓ |
| Gamepad Controller Support | ✓ | ✓ | ✓ |
| ATEM Switcher Integration | ✓ | ✓ | ✓ |
| Firmware Update (Middle Updater) | ✓ | ✓ | ✓ |
| Bitfocus Companion Integration | ✓ | ✓ | ✓ |
| Presets Save & Recall | ✓ | ✓ | ✓ |
| Live View* Lets you see your camera feed in realtime with user friendly OSD. | ✓ | ✓ | ✓ |
| Multi View* Lets you monitor either 4 or 9 cameras side by side. | ✗ | ✗ | ✓ |
| ATEM Link Lets you control any supported camera via ATEM Switchers | ✗ | ✗ | ✓ |
| Visca over IP Controllers | ✗ | ✗ | ✓ |
| Automations Camera Shake, Zoom loops, Preset sequences. | ✗ | ✗ | ✓ |
| Multi-Operator Support Control multiple cameras simultaneously | ✗ | ✗ | ✓ |
| Replicate Settings Copy Gain, WB, Iris, Shutter… to multiple cameras at once | ✗ | ✗ | ✓ |
| Video Output Export the Live View video feed to UltraStudio, HDMI, OBS (Syphon)... | ✗ | ✗ | ✓ |
| Record Center Control Blackmagic HyperDeck and ATEM recording. | ✗ | ✗ | ✓ |
| Canon RC-IP Controllers Drive Middle Control from a Canon RC-IP300 / RC-IP1000 panel. | ✗ | ✗ | ✓ |
Legend: ✓ = Supported · ✗ = Not Supported · Limited = Partial
* Only supports compatible cameras connected over Wi-Fi or Wired LAN. Check support on our compatibility tool
Firmware Update
Updating the APC-R & APC-R Mini
The APC-R , APC-R Mini and APC-R Mini Lite can all be updated using the Middle Updater software.
To update your APC-R, APC-R Mini, or APC-R Mini Lite, follow these steps:
- Install the Middle Updater.
- Make sure the Middle Control software is closed.
- If your APC-R is mounted on a gimbal, make sure the gimbal is turned off.
- Connect your APC-R and press Connect. The updater will check online for a new firmware version.
- If your unit does not show up and you don't see the message "✅ APC-R Detected", connect the unit directly with a USB cable (no USB hub or dongle) — or try a different USB cable.
- Run the update by clicking Start Update.
The update may take up to 5 minutes if all components require updating. If it hangs for longer than 5 minutes, disconnect the APC-R, close and restart the Middle Updater, and try again.
Updating the Middle Remote
To update the Middle Remote, just download and install the latest version of Glue Software . Start Glue, connect your Middle Remote to your laptop and its firmware will be automatically updated if an update is available.
System Requirements
Here are the system requirements for the Middle Control software, with which you can control your camera / gimbal setups.
Operating System
| Platform | Supported Versions | Notes |
|---|---|---|
| macOS | macOS 13+ (Intel & Apple Silicon) | Middle Control 4.0 — recommended OS |
| Windows | Windows 10 (1809+) / 11, 64-bit | Middle Control 4.0 Beta (public beta) or 2.7.4 (stable). ATEM features need ATEM Software Control installed. |
| iOS | — | Middle Control for iOS is in development. Get notified when it is available. |
Host Computer
| Component | Minimum | Recommended |
|---|---|---|
| CPU | 2-core / 4-thread | 4+ cores (e.g. Apple M1 and newer) |
| Memory | 8 GB | 8 GB |
| Storage | 150 MB free | 250MB free |
| GPU | Integrated | Integrated |
If you require any further information, please contact support at [email protected]